TDC provides for all stainless steel materials, when properly maintained, a one-year warranty against all defects in workmanship and construction under normal wear and use of this product.
Floor Supported
This highly versatile style of installation offers modern appeal that will suit any architectural decor concept.The uniform, flush-top design easily adapts to any washroom and the lack of overhead hardware provides a more spacious feel. Secure installation of this style partition requires a solid concrete floor allowing fora minimum 2” penetration anchoring system.
Many options will influence the price of your partitions. To get an estimate, please contact us.
Powder-Coated
Stainless Steel
Plastic Laminate
Diamond Line
Powder-Coated
Powder coated steel partitions offer remarkable quality and durability at an affordable price. Electro-galvanized steel is bonded to a cellular honeycomb core with all edges interlocked and corners welded for maximum structural integrity. The thermosetting powder coating is electrostatically applied to ensure a uniform thickness and produces a finish that is highly resistant to fading, scuffing and staining. Availability in a wide range of contemporary colors makes it simple to find an option that will complement any washroom.
COMPOSITION / CONSTRUCTION OF MATERIALS
Doors are 1” thick, constructed with two 22-gauge sheets of stretcher leveled, commercial quality electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.
Panels are 1” thick, constructed with two 22-gauge sheets of stretcher leveled, commercial quality electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.
Type H/B –Headrail Braced Pilasters are 1-1/4” thick, constructed with two 20-gauge sheets of commercial quality electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. Edges are then interlocked with a continuous roll-formed edge molding. An inverted heavy gauge channel shall be welded into top of the pilaster for additional reinforcing. Pilasters shall have adjustable floor anchor system including an integral jack-leveling device. A polished 3” high stainless steel shoe of one-piece construction shall be supplied to conceal floor anchoring. Tamper proof shoe assembly held in place by means of concealed floor anchor clips –exposed screws are not acceptable. Pilaster tops are securely braced together with a continuous anti-grip headrail of extruded aluminum alloy, polished and clear anodized.
FINISH
Powder coated finishes are applied over electro-galvanized steel containing a zinc coating thickness of .00015”. All components shall be cleaned and degreased prior to application of powder for maximum finish adhesion. A hybrid epoxy/polyester powder is then applied by an electrostatic painting system to ensure uniform thickness. Baking at 345 degrees for 22 minutes cures the finish.
HARDWARE AND FITTINGS
All material components are fully prepared with suitable internal reinforcement to receive all necessary hardware and fittings. TDC Doors supplies factory pre-drilled components for a safer, more efficient and trouble-free installation. All door hinges and strike/keeper will be thru-bolted with sex bolts having theft resistant heads. Appropriate screws supplied for all other hardware and fittings. All fastenings to have a corrosion resistant finish.
Doors:
-Upper and lower door brackets are heavy non-ferrous Zamac castings that become integral part of door as they are imbedded within pre-formed abscesses at time of assembly. Powder coated finish shall match selected door color.
-Top hinge bracket (#102) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over the pilaster edge for maximum durability.
-Stainless steel pin (#101) goes through the door and the top hinge bracket for three-point bearing.
-Bottom hinge bracket (#103) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability. Door operates on opposing nylon cams that are fully recessed and concealed within the lower door bracket. The gravity activated cam assembly provides easy adjustment of door permitting it to rest at any desired open or fully closed position when not latched.
-Concealed latch assembly with stainless steel pin allows for emergency access. Cover plate and turn knob (#104) are heavy, non-ferrous Zamac castings with chrome plated finish. ADA lever handles are supplied on all handicap doors.
-Door strike and keeper (#105) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability.
-Combination coat hook and bumper for inswing doors (#106) or double-prong coat hook for outswing door (#107) shall be cast Zamac with chrome plated finish. Door pull (#109) shall be supplied on all outswing doors. ADA doors receive door pull on both interior and exterior faces. Door bumpers (#108) provided where required.
Wall and Pilaster Brackets:
-Shall be heavy, non-ferrous Zamac castings with chrome-plated finish. The wall anchored pilasters and dividing partition panels shall be attached with two brackets of either double ear or single ear design depending on existing wall condition. Dividing partition panels shall be attached to the “rear” pilaster face with two “U” brackets.
INSTALLATION
Shall be in accordance with TDC’s approved shop drawing and installation instructions with partitions being rigid, plumb, straight and level. Unless stated otherwise, doors and panels are 58” high and mounted 12” above finished floor. Pilasters shall measure 82” from floor to top of headrail.
Stainless Steel
For lasting beauty that blends into any washroom design and will easily withstand years of use, no matter how high-volume, stainless steel is the top choice. Resistant to corrosion, rust, staining, and offering simplified maintenance, this is an ideal option for any heavily trafficked washroom. Stainless Steel Partition material is available in a standard #4 brushed finish, or you may select from a number of optional textured finishes for greater durability and design appeal. Stainless Steel Partition material is available in any of the four design styles.
COMPOSITION / CONSTRUCTION OF MATERIALS
Doors are 1” thick, constructed with two 22-gauge sheets of stretcher leveled type 304 stainless steel #4 finish that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous stainless steel roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.
Panels are 1” thick, constructed with two 22-gauge sheets of stretcher leveled type 304 stainless steel #4 finish that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous stainless steel roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.
Type H/B –Headrail Braced Pilasters are 1-1/4” thick, constructed with two 20-gauge sheets of stretcher-leveled type 304 stainless steel #4 finish that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. Edges are then interlocked with a continuous stainless steel roll-formed edge molding. An inverted heavy gauge channel shall be welded into top of the pilaster for additional reinforcing. Pilasters shall have adjustable floor anchor system including an integral jack-leveling device. A polished 3” high stainless steel shoe of one-piece construction shall be supplied to conceal floor anchoring. Tamper proof shoe assembly held in place by means of concealed floor anchor clips –exposed screws are not acceptable. Pilaster tops are securely braced together with a continuous anti-grip headrail of extruded aluminum alloy, polished and clear anodized.
FINISH
All doors, panels and pilasters shall be type 304 stainless steel with a #4 finish and include a durable plastic film covering to safeguard them during shipment and installation. All components shall have vertical grain finish except panels wider than 58½” –seaming is not acceptable.
HARDWARE AND FITTINGS
All material components are fully prepared with suitable internal reinforcement to receive all necessary hardware and fittings. TDC supplies factory pre-drilled components for a safer, more efficient and trouble-free installation. All door hinges and strike/keeper will be thru-bolted with sex bolts having theft resistant heads. Appropriate screws supplied for all other hardware and fittings. All fastenings to have a corrosion resistant finish.
Doors:
-Upper and lower door brackets are heavy non-ferrous Zamac castings that become integral part of door as they are imbedded within pre-formed abscesses at time of assembly. Satin finish shall closely resemble door finish.
-Top hinge bracket (#102) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over the pilaster edge for maximum durability.
-Stainless steel pin (#101) goes through the door and the top hinge bracket for three-point bearing.
-Bottom hinge bracket (#103) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability. Door operates on opposing nylon cams that are fully recessed and concealed within the lower door bracket. The gravity activated cam assembly provides easy adjustment of door permitting it to rest at any desired open or fully closed position when not latched.
-Concealed latch assembly with stainless steel pin allows for emergency access. Cover plate and turn knob (#104) are heavy, non-ferrous Zamac castings with chrome plated finish. ADA lever handles are supplied on all handicap doors.
-Door strike and keeper (#105) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability.
-Combination coat hook and bumper for inswing door (#106) or double-prong coat hook for outswing door (#107) shall be cast Zamac with chrome plated finish. Door pull (#109) shall be supplied on all outswing doors. ADA doors receive door pull on both interior and exterior faces. Door bumpers (#108) provided where required.
Wall and Pilaster Brackets:
-Shall be heavy, non-ferrous Zamac castings with chrome-plated finish. The wall anchored pilasters and dividing partition panels shall be attached with two brackets of either double ear or single ear design depending on existing wall condition. Dividing partition panels shall be attached to the “rear” pilaster face with two “U” brackets.
INSTALLATION
Shall be in accordance with TDC’s approved shop drawing and installation instructions with partitions being rigid, plumb, straight and level. Unless stated otherwise, doors and panels are 58” high and mounted 12” above finished floor. Pilasters shall measure 82” from floor to top of headrail.
WARRANTY
Plastic Laminate
The recommended choice when the emphasis is on aesthetics and affordability. The high-pressure plastic laminate finish is bonded under pressure to a solid, impact-resistant particleboard core. The smooth, resilient finish provides an easy-to-clean partition that is resistant to surface dirt, staining, and corrosion. Plastic laminate is available in an incredible range of colors and patterns to offer unlimited design flexibility for any new or existing washroom.
COMPOSITION / CONSTRUCTION OF MATERIALS
The core material of all Doors, Panels and Pilasters shall be constructed of 45-lb density, resin-impregnated particle board having flat, smooth surface characteristics. A decorative plastic laminate is then bonded under pressure to core material with a non-toxic, water resistant adhesive. No splices or joints in facing or core are acceptable.
Doors are 1” thick with all external edges and faces covered with decorative plastic laminate. All edge surfaces shall be applied prior to the overlapping face surfaces to seal edge and prevent laminate from being pried loose. Doors are pre-notched and recessed to accommodate concealed controlled gravity type hinges.
Panels are 7/8” thick with all external edges and faces covered with decorative plastic laminate. All edge surfaces shall be applied prior to the overlapping face surfaces to seal edge and prevent laminate from being pried loose.
Pilasters (Type H/B –Headrail Braced) are 1-1/4” thick with external edges and faces covered with decorative plastic laminate. All edge surfaces shall be applied prior to the overlapping face surfaces to seal edge and prevent laminate from being pried loose. Pilasters shall have adjustable floor anchor system including an integral jack-leveling device. A 3” high stainless steel shoe of one-piece construction, matching pilaster profile, shall be supplied to conceal floor anchoring. Tamper proof shoe assembly held in place by concealed floor anchor clips –exposed screws are not acceptable. Pilaster tops are securely braced together with a continuous anti-grip headrail of extruded aluminum alloy, polished and clear anodized.
FINISH
All components shall have edge and face surfaces covered with high pressure, .048 thick (general purpose grade) decorative plastic laminate that meets or exceeds NEMA standards for resistance to wear, burns and moisture.
HARDWARE AND FITTINGS
All material components are fully prepared to receive all necessary hardware and fittings. All door hinges, strike/keeper and brackets will be thru-bolted with sex bolts having theft resistant heads. Appropriate screws supplied for all other hardware and fittings. All fastenings to have a corrosion resistant finish.
Doors: All doors equipped with TDC “Duraglide” hinge sets.
-Upper and lower door brackets are heavy non-ferrous Zamac castings with chrome plated finish. Brackets are installed within factory pre-formed notches.
-Top hinge bracket (#102PL) is a heavy, non-ferrous Zamac casting with chrome plated finish. One-piece design has a 5/8” wrap-around flange that fits over the pilaster edge for maximum durability.
-Stainless steel 3/8” diameter pin (#101PL) goes through the door and the top hinge bracket for three-point bearing.
-Bottom hinge bracket (#103PL) is a heavy, non-ferrous Zamac casting with chrome plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability. Door operates on a stainless steel pintle and opposing nylon cams that are fully recessed and concealed within the lower door bracket. The gravity activated cam assembly provides easy adjustment of door permitting it to rest at any desired open or fully closed position when not latched.
-Surface mounted slide latch (#104PL) is heavy, non-ferrous Zamac casting with chrome plated finish.
-Door strike and keeper (#105PL) is a heavy, non-ferrous Zamac casting with chrome plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability.
-Combination coat hook and bumper for inswing doors (#106) or double-prong coat hook for outswing door (#107) shall be cast Zamac with chrome plated finish. Door pull (#109) shall be supplied on all outswing doors. ADA doors receive door pull on both interior and exterior faces. Door bumpers (#108) provided where required.
Wall and Pilaster Brackets:
-Shall be heavy, non-ferrous Zamac castings with chrome plated finish. The wall anchored pilasters and dividing partition panels shall be attached with two brackets of either double ear or single ear design depending on existing wall condition. Dividing partition panels shall be attached to the “rear” pilaster face with two “U” brackets.
INSTALLATION
Shall be in accordance with TDC’s approved shop drawing and installation instructions with partitions being rigid, plumb, straight and level. Unless stated otherwise, doors and panels are 58” high and mounted 12” above finished floor. Pilasters shall measure 82” from floor to top of headrail.
WARRANTY
Diamond Line
A unique textured metal with Diamond patterns available in a variety of colors for powder coated steel. A powder-coated steel installation offers remarkable quality and durability at an affordable price. A state-of-the-art electrostatic process applies a thermosetting powder coating to an electro-galvanized diamond textured steel partition, creating an installation that combines the strength of steel with a superior protective finish that resists fading, scuffing and staining. The same diamond patterned texture is available in our high quality durable Stainless Steel component. This attractive, durable material will suit any washroom design.
COMPOSITION / CONSTRUCTION OF MATERIALS
Doors are 1” thick, constructed with two 22-gauge sheets of stretcher leveled, commercial quality diamond textured electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.
Panels are 1” thick, constructed with two 22-gauge sheets of stretcher leveled, commercial quality diamond textured electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. All edges are then interlocked with a continuous roll-formed edge molding. All mitered corners are welded and ground smooth. Corner clips will not be acceptable.
Type H/B –Headrail Braced Pilasters are 1-1/4” thick, constructed with two 20-gauge sheets of commercial quality diamond textured electro-galvanized steel that are formed and then laminated under pressure to a sound deadening double-faced honeycomb core. Face plates are welded together at intervals of 18” on center around entire perimeter to insure a rigid one-piece unit. Edges are then interlocked with a continuous roll-formed edge molding. An inverted heavy gauge channel shall be welded into top of the pilaster for additional reinforcing. Pilasters shall have adjustable floor anchor system including an integral jack-leveling device. A polished 3” high stainless steel shoe of one-piece construction shall be supplied to conceal floor anchoring. Tamper proof shoe assembly held in place by means of concealed floor anchor clips –exposed screws are not acceptable. Pilaster tops are securely braced together with a continuous anti-grip headrail of extruded aluminum alloy, polished and clear anodized.
FINISH
Powder coated finishes are applied over diamond textured electro-galvanized steel containing a zinc coating thickness of .00015”. All components shall be cleaned and degreased prior to application of powder for maximum finish adhesion. A hybrid epoxy/polyester powder is then applied by an electrostatic painting system to ensure uniform thickness. Baking at 345 degrees for 22 minutes cures the finish.
HARDWARE AND FITTINGS
All material components are fully prepared with suitable internal reinforcement to receive all necessary hardware and fittings. TDC supplies factory pre-drilled components for a safer, more efficient and trouble-free installation. All door hinges and strike/keeper will be thru-bolted with sex bolts having theft resistant heads. Appropriate screws supplied for all other hardware and fittings. All fastenings to have a corrosion resistant finish.
Doors:
-Upper and lower door brackets are heavy non-ferrous Zamac castings that become integral part of door as they are imbedded within pre-formed abscesses at time of assembly. Powder coated finish shall match selected door color.
-Top hinge bracket (#102) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over the pilaster edge for maximum durability.
-Stainless steel pin (#101) goes through the door and the top hinge bracket for three-point bearing.
-Bottom hinge bracket (#103) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability. Door operates on opposing nylon cams that are fully recessed and concealed within the lower door bracket. The gravity activated cam assembly provides easy adjustment of door permitting it to rest at any desired open or fully closed position when not latched.
-Concealed latch assembly with stainless steel pin allows for emergency access. Cover plate and turn knob (#104) are heavy, non-ferrous Zamac castings with chrome plated finish. ADA lever handles are supplied on all handicap doors.
-Door strike and keeper (#105) is a heavy, non-ferrous Zamac casting with chrome-plated finish. One-piece design has a 5/8” wrap-around flange that fits over pilaster edge for maximum durability.
-Combination coat hook and bumper for inswing doors (#106) or double-prong coat hook for outswing door (#107) shall be cast Zamac with chrome plated finish. Door pull (#109) shall be supplied on all outswing doors. ADA doors receive door pull on both interior and exterior faces. Door bumpers (#108) provided where required.
Wall and Pilaster Brackets:
-Shall be heavy, non-ferrous Zamac castings with chrome-plated finish. The wall anchored pilasters and dividing partition panels shall be attached with two brackets of either double ear or single ear design depending on existing wall condition. Dividing partition panels shall be attached to the “rear” pilaster face with two “U” brackets.
INSTALLATION
Shall be in accordance with TDC’s approved shop drawing and installation instructions with partitions being rigid, plumb, straight and level. Unless stated otherwise, doors and panels are 58” high and mounted 12” above finished floor. Pilasters shall measure 82” from floor to top of headrail.
WARRANTY